The Art of Basic Plumbing When You Install a Bathtub
WebsiteJust how do you really feel on the subject of A Step-by-Step Guide to Installing a Bathtub?
Mounting a tub isn't specifically rocket science, yet it does need strong plumbing, carpentry, and also sometimes, tiling abilities. Changing an old bathtub with a brand-new one is additionally a moderately tough task. If the old tub is readily easily accessible, the task can move immediately; if you need to open up a wall surface to remove the old tub and place the brand-new tub, the task is much harder. In either instance, the job is within a residence handyman's skills, although you will certainly need a helper to leave the old bathtub and also embeded in the new one. Make sure you have actually qualified yourself for the work as well as are comfortable attempting it. Rather than employing a service provider to take control of a halfway-completed project, it is far better to think about employing one before you begin. Possibilities are you may need a specialist plumber to make tube connections.
This write-up will aid you install a brand-new bath tub in your shower room if you have actually already gotten a brand-new tub as well as do not require to change the plan of your previous water pipes.
Your tools as well as product list ought to make up the following:
Removing Old Touches
If you need to replace old faucets with brand-new ones as a part of your installment, then the first thing you should do is separate the water system. After doing so, turn on the taps to drain pipes any type of water remaining in the system. The process of removing the existing faucets can be rather troublesome due to the limited accessibility that is usually the situation.
Use a container wrench (crowsfoot spanner) or a tap device to undo the nut that attaches the supply pipes to the faucets. Have a towel prepared for the remaining water that will certainly originate from the pipelines. Once the supply pipelines have been gotten rid of, utilize the same device to loosen up the nut that holds the taps onto the bath/basin. You will certainly require to stop the solitary faucets from transforming throughout this procedure. As soon as the taps have been gotten rid of, the holes in the bath/basin will need to be cleaned of any kind of old securing substance.
Before going on to fit the brand-new faucets, compare the pipeline connections on the old taps to the brand-new faucets. If the old faucets are longer than the new taps, after that a shank adapter is required for the new faucets to fit.
Suitable New Taps
If the tails of the new taps are plastic, then you will certainly need a plastic port to stop damages to the thread. One end of the port fits on the plastic tail of the tap and also the various other end supplies a connection to the existent supply pipelines.
If you require to fit a monobloc, then you will certainly call for minimizing couplers, which attaches the 10mm pipeline of the monobloc to the typical 15mm supply pipe.
Next off, position the faucet in the mounting opening in the bath/basin making sure that the washers are in location in between the faucet and the sink. Secure the faucet in position with the supplier supplied backnut. Once the faucet is safely in position, the supply pipes can be connected to the tails of the faucets. The taps can either be attached by utilizing corrugated copper piping or with normal tap connectors. The former kind needs to be attached to the tap ends initially, tightening up just by hand. The supply pipelines can later on be attached to the other end. Tighten both ends with a spanner after both ends have been linked.
Setting up the Bathtub
Using the two wood boards under its feet, position the tub in the needed setting. The wooden boards are helpful in uniformly spreading out the weight of the bathtub over the location of the boards instead of focusing all the weight onto 4 tiny points.
The following objective is to make sure that the tub is leveled all round. This can be achieved by examining the spirit level and adjusting the feet on the bath tub until the level reads degree.
To set up taps, fit the bottom of the outermost adaptable tap connector to the ideal supply pipeline by making a compression sign up with; after that do the very same for the other tap.
Activate the supply of water as well as examine all joints as well as brand-new pipework for leakages and tighten them if needed. Load the bath tub as well as additionally inspect the overflow electrical outlet as well as the typical outlet for leakages.
Lastly, deal with the bath paneling as defined in the producer's user's manual. Tiling and sealing around the bathtub must wait until the bathtub has been utilized at least once as this will settle it right into its last placement.
Getting ready for the Installation
First of all, the supporting framework supplied with the bathroom must be fitted (if required) according to the supplier's guidelines. Next off, fit the faucets or mixer to the bathtub. When fitting the faucet block, it is very important to see to it that if the tap comes with a plastic washing machine, it is fitted in between the bathroom and the taps. On a plastic bath, it is likewise practical to fit a sustaining plate under the taps device to avoid strain on the tub.
Fit the flexible tap ports to the bottom of both taps making use of 2 nuts as well as olives (occasionally supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and afterwards pass the outlet via the hole in the bath. Make use of the nut provided by the producer to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the versatile overflow pipe to the overflow outlet. After that, screw the pipe to the overflow face which ought to be fitted inside the bathroom. Ensure you use all of the supplied washers.
Attach the trap to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Attach all-time low of the overflow tube in a comparable manner.The bath must now be ready to be suited its last setting.
Tiling Around the Tub
In the area where the bathroom satisfies the tile, it is essential to secure the joins with a silicone rubber caulking. This is important as the installation can move sufficient to crack a stiff seal, causing the water to pass through the wall between the bathroom and the tiling, bring about complications with moisture and also possible leaks to the ceiling listed below.
You can pick from a variety of coloured sealants to assimilate your components and also fittings. They are sold in tubes as well as cartridges, and are capable of securing voids approximately a size of 3mm (1/8 inch). If you have a larger gap to fill, you can fill it with spins of drenched newspaper or soft rope. Bear in mind to always load the bath tub with water prior to sealing, to permit the movement experienced when the tub remains in usage. The sealant can fracture relatively early if you do not take into consideration this motion before securing.
Additionally, ceramic coving or quadrant tiles can be used to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as cut to dimension, are additionally conveniently readily available on the market. It is advisable to fit the floor tiles using waterproof or water resistant adhesive as well as cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I found that page on How to Install a Bathtub Yourself when surfing the search engines. Are you aware of anybody else who is enthusiastic about the niche? Feel free to share it. We appreciate reading our article about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.
Quality service? Ring us.